Our Projects

Recent work across Colorado Springs

This gallery shows the kinds of projects we take on across the Pikes Peak region. Project photos from completed jobs will be added here as they’re photographed. Each card below is a sample layout placeholder until real project photos are available.

Ready to start a project like one of these? Request a free estimate or call (719) 555-0134.

What a typical project looks like — in detail

The cards above show the kinds of work we do. What follows is what each kind actually involves: the scope, the spec decisions, and the details that determine whether it lasts. These are typical project descriptions, not past-job case studies — real project photos will be added here as they’re completed and photographed. Read the one that matches your project to understand what your estimate will cover.

Driveway replacement

A full driveway tear-out and replacement is one of the most common residential jobs we do — and one of the most commonly underbuilt by cheap contractors. The typical scope: saw-cut and break out the old slab, haul off all debris, excavate to establish a proper subgrade, and place a compacted aggregate base. The new slab is usually 4 to 6 inches thick depending on vehicle loads, reinforced with rebar or wire mesh, and poured with an air-entrained mix for freeze-thaw resistance. Control joints are spaced to manage cracking, the surface gets a broom finish for traction, and the driveway is graded so water sheets off to the sides rather than pooling or running toward the garage.

The details that matter: the apron where the driveway meets the street (in the public right-of-way, often with its own requirements), the thickness at the garage transition where vehicles turn and load the edge, and drainage along the sides. A driveway poured without attention to the apron and the garage interface will crack at exactly those stress points within a few seasons. Typical timeline: two to four working days for a standard two-car driveway, plus curing time before vehicle traffic (about 7 days).

Stamped concrete patio

A stamped patio gives you the look of stone, slate, or wood plank with the durability and price structure of concrete — but only if the base and the stamping are both done right. The scope mirrors standard flatwork (excavation, compacted base, reinforcement, air-entrained mix) with a different surface process: after the concrete is placed and screeded, color hardener or integral color goes in, release agent is applied, and stamps are pressed in sequence while the concrete is at exactly the right set. Timing is everything — stamp too early and the pattern is mushy; too late and it won’t take.

After stamping, the slab cures, gets washed, and is sealed — and sealing isn’t optional on stamped work. The sealer deepens the color and protects the textured surface from freeze-thaw and staining. Plan on resealing every 2 to 3 years to keep it looking right. Typical timeline: two to three days of work for an average patio, with the sealer applied after initial cure. If you’re comparing stamped bids, ask about the base spec and the sealer schedule — a stamped surface on a bad base is expensive decoration over a future failure.

New home foundation

Foundations are the highest-stakes concrete we pour: everything above depends on everything below. The typical scope starts with excavation to the depth the design requires (below local frost depth for footings), forming and pouring footings, then stem walls or full basement walls, with reinforcement per the structural design. For slab-on-grade foundations, the scope includes subgrade prep, a compacted base, vapor barrier where specified, reinforcement, and the slab pour itself.

What distinguishes a good foundation contractor: attention to the soil (expansive clay pockets in the Pikes Peak region need specific handling), accurate forming (out-of-square or out-of-level foundations haunt every trade that follows), proper consolidation of the concrete in the forms, and curing protection. Foundations require permits and inspections — we coordinate the inspection sequence so it doesn’t stall your build. Typical timeline: one to three weeks depending on foundation type, weather, and inspection scheduling. This is not a job to rush or to award on price alone.

Commercial parking lot

Commercial flatwork lives a harder life than residential: heavier vehicles, more of them, turning loads that tear at surfaces, and drainage across large areas. A typical parking lot scope includes demolition of failed sections (or full-depth removal for a rebuild), subgrade preparation and proof-rolling, a thick compacted base, and concrete placed at 5 to 8 inches depending on traffic — thicker in drive lanes and turning areas, with reinforcement and jointing designed for the loads. Drainage is engineered across the whole lot: catch basins, trench drains, and slopes that move water without ponding, because standing water plus freeze-thaw destroys commercial pavement.

Commercial work also means coordination: striping, ADA-compliant walks and ramps, curb and gutter, dumpster pads, and sometimes phased construction so the business stays open. We schedule pours to minimize disruption — early starts, phased sections, clear communication with the property manager. Typical timeline: one to several weeks depending on size and phasing. If you’re a property manager comparing bids, the base section and the jointing plan are where cheap quotes hide their cuts.

Retaining wall

A retaining wall is structural concrete holding back soil — it fails in slow, expensive ways when it’s underbuilt. The typical scope: excavation for the footing, a reinforced footing poured below frost depth, wall forms with reinforcement tied to the footing steel, concrete placement with proper consolidation, and — critically — drainage behind the wall. Drainage is the difference between a wall that stands for decades and one that leans, cracks, or blows out: a perforated drain pipe at the footing, free-draining backfill, and weep holes or outlets so hydrostatic pressure never builds up.

Walls above certain heights require engineering and permits; we’ll tell you at the estimate whether your wall crosses that line. Typical timeline: one to two weeks for a standard residential wall, longer for tall or tiered walls. Never hire a retaining wall on price alone — the footing, the steel, and the drainage are invisible after backfill, which is exactly why they’re the first things a cheap bid deletes.

Garage slab and apron

A garage floor takes concentrated loads — vehicle tires, jacks, tool chests — on a relatively small slab, often with moisture coming up from below. The typical scope: excavation and compacted base, vapor barrier to control moisture transmission, reinforcement (garage slabs benefit from rebar more than most residential flatwork), and a 4-to-6-inch slab with a smooth trowel finish. The apron — the section from the garage door to the driveway or street — gets extra attention: it’s the transition zone, it takes turning loads, and it often sits in the right-of-way.

Finish options include a plain trowel finish, or an epoxy coating applied after cure for a chemical-resistant, easy-clean surface (see below). Typical timeline: one to two days of work plus cure time. If your garage floor is spalling or dusting, the cause is usually a bad original mix or no vapor barrier — both fixable in the replacement spec.

Epoxy garage floor

Epoxy coatings turn a plain garage slab into a chemical-resistant, low-maintenance surface — but the coating is only as good as the prep. The typical scope: diamond grinding or shot-blasting the existing slab to open the concrete’s pores (this is the step cheap coating jobs skip, and it’s why they peel), repair of cracks and spalls, then the epoxy system itself — primer, build coats, decorative flake or solid color, and a topcoat. Moisture testing matters: a slab with high moisture vapor transmission will delaminate a coating unless it’s addressed.

Epoxy isn’t paint, and it isn’t a fix for a structurally failed slab — if the concrete is heaving or breaking apart, replacement is the honest answer. But on a sound slab, a properly prepped epoxy floor lasts years under daily vehicle traffic. Typical timeline: two to three days including prep and cure between coats. Ask any coating bidder about their surface prep method specifically; “we acid-etch” is a weaker answer than mechanical grinding.

Sidewalk and walkway

Walkways seem simple, which is why they’re so often done badly: poured thin, on no base, with no thought to drainage, and heaving within a few winters. Our typical scope: excavation, compacted base, 4-inch slab with reinforcement, broom finish for slip resistance, control joints at proper spacing, and grading that sheds water. For walks along a foundation, we slope away from the house — a walkway that ponds water against a foundation is a basement problem wearing a sidewalk costume.

Public sidewalks and the apron at the street may fall under city right-of-way rules with specific thickness, finish, and permit requirements — we handle that. Typical timeline: one to two days for a standard residential walk. If your existing walk has settled or heaved, ask about slab lifting before assuming replacement: a settled-but-sound slab can often be lifted and releveled for less than a tear-out.

Pool deck

Pool decks combine everything hard about exterior concrete: constant water exposure, bare feet (so the finish must be slip-resistant but not cheese-grater rough), and chemical exposure from pool water. The typical scope: excavation and compacted base with careful grading (pool decks must shed water away from the pool and the house), reinforced 4-inch slab, air-entrained mix, and a finish chosen for traction — broom, exposed aggregate, or a textured decorative finish. Control joints are placed to manage cracking without creating trip edges.

Coping and the deck-to-pool interface get special attention: that’s where movement and water concentrate. Sealing is strongly recommended — pool chemicals and constant wetting are brutal on unsealed concrete. Typical timeline: two to four days depending on size and finish. If you’re comparing pool deck bids, the drainage plan and the finish specification are the two things to scrutinize.

What to expect when you call

Find the project type above that matches yours, then call (719) 555-0134 — you’ll already know what questions we’ll ask and what the estimate will cover, which makes the whole process faster. We’ll schedule a free on-site visit, measure, talk through the spec decisions described above as they apply to your site, and give you a written quote. No obligation, no pressure. The call takes five minutes; the estimate gives you everything you need to decide.

Not sure which project type fits?

Many real projects cross the categories above — a driveway replacement that needs a retaining wall at the edge, a patio that ties into a new sidewalk, a garage slab with an epoxy finish. That’s exactly why we’re full-service: one estimate, one crew, one schedule for the whole thing. Describe what you’ve got and what you want at contact us, and we’ll tell you honestly what it takes — including when the right answer is a repair instead of a replacement.